Журнал Российского общества по неразрушающему контролю и технической диагностике
The journal of the Russian society for non-destructive testing and technical diagnostic
 
| Русский Русский | English English |
 
Главная Текущий номер
28 | 03 | 2024
2018, 06 июнь (June)

DOI: 10.14489/td.2018.06.pp.028-033

Алиев А. Р., Тимофеев Ю. М., Халатов Е. М.
МЕТОДИКА УПРОЩЕННОГО РАСЧЕТА ПАРАМЕТРОВ ПРОЦЕССА НАПОЛНЕНИЯ ПОЛОСТЕЙ ИЗДЕЛИЙ РАКЕТНО-КОСМИЧЕСКОЙ ТЕХНИКИ ПРИ ПНЕВМОВАКУУМНЫХ ИСПЫТАНИЯХ
(с. 28-33)

Аннотация. Рассмотрена схема системы наполнения полостей испытываемых объектов – составной части установки для пневмовакуумных испытаний устройств и агрегатов ракетно-космической техники. Предложена упрощенная методика определения параметров и оценки работоспособности схемы при обеспечении заданных требований технологии испытаний.

Ключевые слова:  пневмовакуумные испытания, автоматический режим наполнения, математическая модель, параметры процесса.

 

Aliev A. R., Timofeyev Yu. M., Khalatov E. M.
SIMPLIFIED ANALYSIS PROCEDURE OF PARAMETERS FOR FILLING THE CHAMBERS OF ROCKET AND SPACE ENGINEERING PRODUCTS DURING PNEUMOVACUUM TESTS
(pp. 28-33)

Abstract. This paper treats of a circuit of the system for filling the chambers of objects under test as a constituent of the installation for pneumovacuum tests of devices and units of rocket and space engineering. The strictly regulated requirements are imposed upon the process of filling of products chambers during pneumovacuum tests: filling rate must be specified, gas temperature in the process of filling must not exceed a predetermined value, fill-up time to a predetermined pressure value must be minimum. Filling of the object chamber under test, subject to demands made, is carried out in a stepwise manner. Two processes – filling and holding under pressure are carried out at each stage.Within the limits of this paper, consideration is being given to the analysis of the first of two stages of filling system resulting in development of simplified technique of parameter determination and functionality evaluation of the circuit under the provision of specified requirements of devices and units of rocket and space engineering test procedure. The proposed technique is illustrated by an example of analysis of filling process of spherical product chamber.The proposed technique is intended for use by specialists engaged in design of the systems for filling rocket-and-space hardware during pneumovacuum tests, at the stage of formation of their circuits and functionality evaluation.

Keywords: pneumovacuum tests, automatic mode of filling, mathematical model, parameters of process.

Рус

А. Р. Алиев, Ю. М. Тимофеев, Е. М. Халатов (Конструкторское бюро «Арматура» – филиал АО «Государственный космический научно-производственный центр им. М. В. Хруничева», г. Ковров, Россия) E-mail: Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра. , Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра. , Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.  

Eng

A. R. Aliev, Yu. M. Timofeyev, E. M. Khalatov (Design Bureau “Armatura” – branch of JSC “Khrunichev State research and Production Space Center”, Kovrov, Russia) E-mail: Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра. , Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра. , Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.  

Рус

1. Арзуманов Ю. Л., Халатов Е. М., Чекмазов В. И., Чуканов К. П. Основы построения математических моделей функционирования устройств пневмоавтоматики: учеб. пособие. М.: ИД «Спектр», 2015. 130 с.
2. Арзуманов Ю. Л., Халатов Е. М., Чекмазов В. И. Основы проектирования систем регулирования параметров газа в комплексах газоавтоматики. М.: ИД «Спектр», 2013. 264 с.
3. Подчуфаров Б. М., Подчуфаров Ю. Б. Тепломеханика: учеб. пособие. Тула: ТулПИ, 1985. 104 с.

Eng

1. Arzumanov Yu. L., Halatov E. M., Chekmazov V. I., Chukanov K. P. (2015). Fundamentals of constructing mathematical models for the operation of pneumatic automation devices: textbook. Moscow: ID «Spektr». [in Russian language]
2. Arzumanov Yu. L., Halatov E. M., Chekmazov V. I. (2013). Basics of designing systems for regulating gas parameters in gasautomatics complexes. Moscow: ID «Spektr». [in Russian language]
3. Podchufarov B. M., Podchufarov Yu. B. (1985). Heat mechanics: textbook. Tula: TulPI. [in Russian language]

Рус

Статью можно приобрести в электронном виде (PDF формат).

Стоимость статьи 350 руб. (в том числе НДС 18%). После оформления заказа, в течение нескольких дней, на указанный вами e-mail придут счет и квитанция для оплаты в банке.

После поступления денег на счет издательства, вам будет выслан электронный вариант статьи.

Для заказа скопируйте doi статьи:

10.14489/td.2018.06.pp.028-033

и заполните  форму 

Отправляя форму вы даете согласие на обработку персональных данных.

.

 

Eng

This article  is available in electronic format (PDF).

The cost of a single article is 350 rubles. (including VAT 18%). After you place an order within a few days, you will receive following documents to your specified e-mail: account on payment and receipt to pay in the bank.

After depositing your payment on our bank account we send you file of the article by e-mail.

To order articles please copy the article doi:

10.14489/td.2018.06.pp.028-033

and fill out the  form  

 

.

 

 
Поиск
На сайте?
Сейчас на сайте находятся:
 64 гостей на сайте
Опросы
Понравился Вам сайт журнала?
 
Баннер
Rambler's Top100 Яндекс цитирования