10.14489/td.2025.10.pp.051-056

2025, 10 October

DOI: 10.14489/td.2025.10.pp.051-056

Mokritsky B. Ya., Kosmynin A. V., Sysoev O. E.
INVESTIGATION OF DIAGNOSTIC CRITERIA FOR THE MILLING OF HIGH-HARDNESS MATERIALS WITH PREFABRICATED END MILLS
(pp. 51-56)

Abstract. The technological cutting system must be maintained in optimal condition under any external influence on it. It is important to choose what you can use to support it. The results of a study of the possibility of technical diagnostics of the state of the technological cutting system “machine tool‒device‒tool‒part” for monitoring the wear spread of the cutting plates of a prefabricated milling cutter at different positions of the milling cutter and the workpiece are presented. As a result, recommendations have been developed that make it possible to diagnose the condition of the technological cutting system based on the results of monitoring the wear spread of the cutting plates at different positions of the milling cutter and the workpiece. It is found that the magnitude of the spread decreases with the transition from the initial position to the central position and then to the extreme position. This allows us to recommend milling with the specified milling cutter as the final (finishing) at the extreme position of the milling cutter and the workpiece, and the central position and the initial position as the preceding half–finished and rough milling.

Keywords: diagnostics of the state of the technological cutting system, milling of high-hardness layers, and the variation in the wear of the cutting plates at different positions of the milling cutter and the workpiece.

+ - About the Authors Click to collapse

B. Ya. Mokritsky, A. V. Kosmynin, O. E. Sysoev (Komsomolsk-on-Amur State University, Komsomolsk-on-Amur, Russia) E-mail: Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра. , Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра. , Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.

+ - References Click to collapse

1. Mokritsky, B. Ya., & Skripilev, A. A. (2022). Control of milling high-hardness workpieces. Vestnik Mashinostroeniya, (12), 72–75. [in Russian language]. https://doi.org/10.36652/0042-4633-2022-12-72-75
2. Mokritsky, B. Ya., & Mokritskaya, E. B. (2021). Blade processing of hardened materials. Part 3. Processing of parts workpieces hardened with high-hardness surfacing. Uprochnyayushchie Tekhnologii i Pokrytiya, 17(11), 495–497. [in Russian language]. https://doi.org/10.36652/1813-1336-2021-17-11-495-497
3. Vereshchaka, A. A., Vereshchaka, A. S., & Gri¬goriev, S. N. (2012). Multilayer-composite nanostructured coatings for cutting tools operating in severe conditions. Uprochnyayushchie Tekhnologii i Pokrytiya, (12), 3–11. [in Russian language]
4. Promptov, A. I., Livshits, O. P., Zamashchikov, Yu. I., & Makarov, R. V. (2000). Recommendations for selecting cutting conditions for finishing operations of turning, boring, and face milling with tools equipped with hard alloy, ceramics, and composite. Izd-vo IrGTU. [in Russian language]
5. Deederich, N. (1968). Metallisher Zwischeushichten im Bereich der Aufbanschneidesbildung. Ind.-Anz., 90(24), 457–460.
6. Fuch, M., & Scheffer, M. (1999). Ab initio pseudopotentieals for electronic structure calgulations of polu-atomic sustems using density-finctional theory. Comp. Phys. Commun., 119, 67–11.
7. Schneider, I. M. (2006). Effect of transition metal additives on electronic structure and elastic properties of TiAl and Ti3Al. Phys. Rev. B, 74(17), 41–51.

+ - Purchase digital version of a single article Click to collapse

This article is available in electronic format (PDF).

The cost of a single article is 700 rubles. (including VAT 20%). After you place an order within a few days, you will receive following documents to your specified e-mail: account on payment and receipt to pay in the bank.

After depositing your payment on our bank account we send you file of the article by e-mail.

To order articles please copy the article doi:

10.14489/td.2025.10.pp.051-056

and fill out the form