Журнал Российского общества по неразрушающему контролю и технической диагностике
The journal of the Russian society for non-destructive testing and technical diagnostic
 
| Русский Русский | English English |
 
Главная Архив номеров
29 | 03 | 2024
2017, 12 декабрь (December)

DOI: 10.14489/td.2017.12.pp.024-029

Савин И. С., Славинская Е. А., Терехин И. В.
ВИХРЕТОКОВЫЙ КОНТРОЛЬ УРОВНЯ МЕТАЛЛА В КРИСТАЛЛИЗАТОРЕ С ПОМОЩЬЮ ПРЕОБРАЗОВАТЕЛЯ ЭКРАННОГО ТИПА
(c. 24-29)

Аннотация. Рассмотрены годографы экранного вихретокового преобразователя положения уровня жидкого металла в сортовом кристаллизаторе. Исследованы сигналы от контролируемого параметра – уровня расплавленной стали и мешающего параметра – изменения температуры стенок кристаллизатора. По результатам моделирования и лабораторного эксперимента даны рекомендации по выбору режима контроля и способа измерения уровня стали.

Ключевые слова:  вихретоковый контроль, непрерывная разливка стали, преобразователь уровня металла.

 

Savin I. S., Slavinskaya E. A., Terekhin I. V.
EDDY CURRENT TESTING OF THE METAL LEVEL IN THE CRYSTALLIZER USING A SCREEN-TYPE CONVERTER
(pp. 24-29)

Abstract. The properties of the screen eddy current transducer of the metal level position in the mold crystallizer are investigated in the article. A transmission probe consists of the exciting coil and array of pick-up coils that are located on opposite mould’s walls. The design of probe allows testing directly molten metal in the mould, however detuning the wall’s heat is required. According to the results of the laboratory experiment possibility of the directly molten metal’s testing is confirmed. In addition, an exciting frequency providing the highest signal-to-ratio is selected. An interdisciplinary numerical model of the billet mould with the transmission eddy current probes was built. Based on modeling results hodographs from molten metal, mould’s temperature changes and overall hodograph under the influence of both factors simultaneously are received. The overall hodograph is non-linear and it can’t be represented as sum of hodographs from metal and mould temperature. One of the differentiation methods is the two-frequency excitation, for which it is necessary to choose frequencies for testing temperature and level of metal separately. Besides, it is offered to apply distribution of signals from the oscillation of the mould for testing the molten metal level.

Keywords: eddy current testing, continuous steel casting, mould metal level probe.

Рус

И. С. Савин, Е. А. Славинская, И. В. Терехин (Национальный исследовательский университет «Московский энергетический институт», Москва, Россия) E-mail: Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра. , Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра. , Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.  

Eng

I. S. Savin, E. A. Slavinskaya, I. V. Terekhin (National Research University “Moscow Power Engineering Institute”, Moscow, Russia) E-mail: Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра. , Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра. , Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.  

Рус

1. Терехин И. В. Разработка вихретоковых средств контроля уровня жидкого металла в гильзовом кристаллизаторе при непрерывной разливке стали: дис. … канд. техн. наук. М., 2008.
2. Mörmann J., Schmid S., Spagnul. Recent progress in fast and accurate meniscus level measurement for continuous casting machines // Proc. 7th European Continuous Casting Conference (ECCC) 2011, 27 June – 1 July 2011, Dusseldorf, 2011.
3. Ермолов И. Н., Останин Ю. Я. Методы и средства неразрушающего контроля качества: учеб. пособие для инж.-техн. спец. вузов. М.: Высш. шк., 1988.

Eng

1. Terekhin I. V. (2008). Development of eddy current testing means for monitoring the level of liquid metal in a sleeve mold during the continuous casting of steel. PhD thesis. Moscow. [in Russian language]
2. Mörmann J., Schmid S., Spagnul. (2011). Recent progress in fast and accurate meniscus level measurement for continuous casting machines. Proc. 7th European Continuous Casting Conference (ECCC) 2011, 27 June – 1 July 2011, Dusseldorf.
3. Ermolov I. N., Ostanin Iu. Ia. (1988). Methods and means of non-destructive quality control: a manual for engineering and technical special universities. Moscow: Vysshaia shkola. [in Russian language]

Рус

Статью можно приобрести в электронном виде (PDF формат).

Стоимость статьи 350 руб. (в том числе НДС 18%). После оформления заказа, в течение нескольких дней, на указанный вами e-mail придут счет и квитанция для оплаты в банке.

После поступления денег на счет издательства, вам будет выслан электронный вариант статьи.

Для заказа статьи заполните форму:

Форма заказа статьи



Дополнительно для юридических лиц:


Type the characters you see in the picture below



.

Eng

This article  is available in electronic format (PDF).

The cost of a single article is 350 rubles. (including VAT 18%). After you place an order within a few days, you will receive following documents to your specified e-mail: account on payment and receipt to pay in the bank.

After depositing your payment on our bank account we send you file of the article by e-mail.

To order articles please fill out the form below:

Purchase digital version of a single article


Type the characters you see in the picture below



 

 

 

 

 

.

.

 

 
Поиск
На сайте?
Сейчас на сайте находятся:
 28 гостей на сайте
Опросы
Понравился Вам сайт журнала?
 
Баннер
Rambler's Top100 Яндекс цитирования