Журнал Российского общества по неразрушающему контролю и технической диагностике
The journal of the Russian society for non-destructive testing and technical diagnostic
 
| Русский Русский | English English |
 
Главная Архив номеров
29 | 03 | 2024
2021, 02 февраль (February)

DOI: 10.14489/td.2021.02.pp.060-064

Терехин И. В., Чернова Е. А.
ВИХРЕТОКОВЫЙ ПРЕОБРАЗОВАТЕЛЬ ДЛЯ КОНТРОЛЯ УРОВНЯ МЕТАЛЛА В СОРТОВОМ КРИСТАЛЛИЗАТОРЕ ПРИ РАЗЛИВКЕ СО ШЛАКООБРАЗУЮЩЕЙ СМЕСЬЮ
(c. 60-64)

Аннотация. Представлены результаты промышленных испытаний вихретокового прибора прямого контроля уровня металла при непрерывной разливке стали с использованием шлакообразующей смеси на сортовом кристаллизаторе. Проведена апробация нового алгоритма определения уровня металла, состоящего в выделении переменной составляющей сигнала, вызванной изменением положения мениска жидкой стали. Для отстройки от влияния электромагнитного перемешивателя предложен способ цифровой обработки сигналов, основанный на применении гребенчатого фильтра.

Ключевые слова:  вихретоковый контроль, непрерывная разливка стали, прямой контроль уровня металла, электромагнитный перемешиватель.

 

Terekhin I. V., Chernova E. A
EDDY CURRENT MOLD LEVEL SENSOR UNDER CONTINUOUS CASTING OF STEEL USING MOLD FLUX
(pp. 60-64)

Abstract. The paper deals with the industrial test of eddy current device for direct metal level control under continuous casting of steel using mold flux. The new algorithm of detection meniscus level has been proposed. The algorithm consists of selecting of a signal variable component caused by oscillation of steel meniscus. The way of filtering the noise from electromagnetic stirrer based on the comb filter application has been developed. The paper deals with the industrial test of eddy current sensor for molten metal level detecting under continuous casting of steel using mold flux. The new algorithm of detection meniscus level has been proposed. The algorithm consists of extracting the signal variable component caused by oscillations of steel meniscus which are intended to reduce friction on the strand surface. The way of filtering the noise from electromagnetic stirrer based on the comb filter application has been developed. It has been proven that the developed algorithm can completely remove the influence of the electromagnetic stirrer field. The industrial test results show that the readings of eddy current and radioactive isotope sensor are synchronous both in a stationary casting mode and in case of fast metal level change. Moreover the eddy current steel level sensor has high precision of steel level measurement, quick response time and low noise level free from the influence of mold flux.

Keywords: eddy current testing, continuous casting of steel, direct metal level control, electromagnetic stirrer

Рус

И. В. Терехин, Е. А. Чернова (Национальный исследовательский университет «Московский энергетический институт», Москва, Россия) Е-mail: Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра. , Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.  

Eng

I. V. Terekhin, E. A. Chernova (National Research University  “Moscow Power Engineering Institute”, Moscow, Russia) 

Рус

1. Габелая Д. И., Кабаков З. К., Грибкова Ю. В. Теплофизические основы технологии непрерывной разливки стали. М. – Вологда: Инфра-Инженерия, 2019. 400 с.
2. Терехин И. В., Романов С. А., Савин И. С. Электромагнитный датчик уровня металла в сортовом кристаллизаторе // Металлург. 2018. № 8. С. 13 – 18.
3. Мерман Д., Шмид Й., Спагнул С. Быстрое и точное определение уровня металла в кристаллизаторах машин непрерывного литья заготовок // Черные металлы. 2012. № 3. С. 53 – 61.
4. Савин И. С., Терехин И. В. Снижение погрешности от ЭМП при измерении уровня расплава вихретоковым методом // Датчики и системы. 2017. № 6. С. 42 – 49.
5. Савин И. С., Терехин И. В. Улучшение динамических характеристик матричного вихретокового датчика уровня металла, встроенного в кристаллизатор // Приборы и системы. Управление, контроль, диагностика. 2016. № 6. С. 20 – 25.
6. Ferreira J. L., Wu Y., Aarts R. M. Enhancement of the Comb Filtering Selectivity Using Iterative Moving Average for Periodic Waveform and Harmonic Elimination // Journal of Healthcare Engineering. 2018. V. 2018. No. 2. P. 1 – 14.

Eng

1. Gabelaya D. I., Kabakov Z. K., Gribkova Yu. V. (2019). Thermophysical Foundations of Continuous Steel Casting Technology. Moscow – Vologda: Infra-Inzheneriya. [in Russian language]
2. Terekhin I. V., Romanov S. A., Savin I. S. (2018). Electromagnetic metal level sensor in a bar mold. Metallurg, (8), pp. 13 – 18. [in Russian language]
3. Merman D., Shmid Y., Spagnul S. (2012). Fast and accurate determination of the level of metal in the molds of continuous casting machines. Chernye metally, (3), pp. 53 – 61. [in Russian language]
4. Savin I. S., Terekhin I. V. (2017). Reducing the error from EMF when measuring the level of the melt by the eddy current method. Datchiki i sistemy, (6), pp. 42 – 49. [in Russian language]
5. Savin I. S., Terekhin I. V. (2016). Improvement of the dynamic characteristics of the matrix eddy current metal level sensor built into the mold. Pribory i sistemy. Upravlenie, kontrol', diagnostika, (6), pp. 20 – 25. [in Russian language]
6. Ferreira J. L., Wu Y., Aarts R. M. (2018). Enhancement of the Comb Filtering Selectivity Using Iterative Moving Average for Periodic Waveform and Harmonic Elimination. Journal of Healthcare Engineering, Vol. 2018, (2), pp. 1 – 14.

Рус

Статью можно приобрести в электронном виде (PDF формат).

Стоимость статьи 450 руб. (в том числе НДС 18%). После оформления заказа, в течение нескольких дней, на указанный вами e-mail придут счет и квитанция для оплаты в банке.

После поступления денег на счет издательства, вам будет выслан электронный вариант статьи.

Для заказа скопируйте doi статьи:

10.14489/td.2021.02.pp.060-064

и заполните  форму 

Отправляя форму вы даете согласие на обработку персональных данных.

.

 

Eng

This article  is available in electronic format (PDF).

The cost of a single article is 450 rubles. (including VAT 18%). After you place an order within a few days, you will receive following documents to your specified e-mail: account on payment and receipt to pay in the bank.

After depositing your payment on our bank account we send you file of the article by e-mail.

To order articles please copy the article doi:

10.14489/td.2021.02.pp.060-064

and fill out the  form  

 

.

 

 
Поиск
На сайте?
Сейчас на сайте находятся:
 20 гостей на сайте
Опросы
Понравился Вам сайт журнала?
 
Баннер
Rambler's Top100 Яндекс цитирования