Журнал Российского общества по неразрушающему контролю и технической диагностике
The journal of the Russian society for non-destructive testing and technical diagnostic
 
| Русский Русский | English English |
 
Главная Архив номеров
28 | 03 | 2024
2014, 11 ноябрь (November)

DOI: 10.14489/td.2014.011.pp.014-018

Якимов Е. В., Гольдштейн А. Е., Булгаков В. Ф., Алхимов Ю. В., Белянков В. Ю.
ИЗМЕРЕНИЕ ТОЛЩИНЫ СТЕНКИ ЭЛЕКТРОПРОВОДЯЩИХ ТРУБ ВИХРЕТОКОВЫМ МЕТОДОМ ПРИ ЗНАЧИТЕЛЬНЫХ ИЗМЕНЕНИЯХ ЗАЗОРА
(с. 14-18)

Аннотация. Описан двухчастотный метод отстройки от влияния изменения зазора между вихретоковым преобразователем и трубой на показания вихретокового толщиномера электропроводящих труб. Представлена измерительная установка для исследования двухчастотного вихретокового метода измерения толщины стенок легкосплавных бурильных труб. Приведены результаты ис-следования зависимостей амплитуды и фазы сигналов от толщины стенки труб в диапазоне от 5,1 до 11,9 мм и зазора в диапазо-не от 1,5 до 14,5 мм. Предложены алгоритмы вычислительной обработки измерительной информации. Использована полиноми-альная аппроксимация зависимости фазы низкочастотного сигнала от толщины стенки трубы, коэффициенты которой также являются полиномиальными функциями зазора. Показано, что применение алгоритмов отстройки позволяет уменьшить погрешность от изменения зазора на 5 мм более чем в 10 раз (с 4,1 до 0,2 мм).

Ключевые слова:  вихретоковый толщиномер, легкосплавные бурильные трубы, зазор между трубой и преоб-разователем.

 

Yakimov E.V., Goldstein A.E., Bulgakov V.F., Alkhimov Yu.V., Belyankov V.Yu.
MEASURING OF ELECTROCONDUCTIVE PIPE WALL THICKNESS USING EDDY-CURRENT METHOD IN PRESENCE OF LARGE GAP BETWEEN PIPE AND TRANSDUCER
(pp. 14-18)

Abstract. The paper describes a dual-frequency method of detuning from the effect of the change in the gap between the pipe and the eddy-current transducer on the readings of the eddy-current thickness gauge for electrically conductive pipes. Light-alloy drill pipes made of aluminum alloys are used to perform workover in structural, exploration and production drilling. Due to the fact that the pipe walls are worn during in-service use, the wall thickness of the main pipe section must be controlled. Eddy current method provides high efficiency control and sensitivity, and it can be used to perform non-contact measurement. However, the eddy-current transducer signals significantly depend on the gap size between the transducer and the pipe. Excitation of the eddy-current transducer with the signal of the same frequency does not allow extracting information on the gap size. A dual-frequency method is more appropriate for this purpose. The dependencies of the signal amplitude and phases on the wall thicknesses ranging from 5,1 to 11,9 mm and on the gap size ranging from 1,5 to 14,5 mm were obtained using the measuring apparatus developed to study the dual-frequency eddy-current technique. The signal, which is the sum of the low frequency (125 Hz) and high frequency (2 kHz) harmonic signals, was fed to the transducer excitation winding. The results of the research show that the dependence of the phase of a low-frequency signal on the pipe wall thickness can be approxi-mated with an error of less than 0,18 mm by the 4th order polynomials, which coefficients are also the polynomial functions of the gap. The signal amplitude can be used to determine the gap size since the amplitude slightly depends on the pipe thickness and it significantly decreases as the pipe gap increases. The approximation of the dependence with an error of less than 0,08 mm can be performed as the sum of two exponential functions. The application of the proposed algorithms of detuning can reduce the error by more than tenfold (from 4,1 mm to 0,2 mm) in case of the gap size varies by 5 mm.

Keywords: eddy-current thickness meter, light-alloy drill pipe, gap between pipe and transducer.

Рус

Е. В. Якимов, А. Е. Гольдштейн, В. Ф. Булгаков, Ю. В. Алхимов, В. Ю. Белянков (Национальный исследовательский томский политехнический университет) E-mail: Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.  

Eng

E. V. Yakimov, A. E. Goldstein, V. F. Bulgakov, Yu. V. Alkhimov, V. Yu. Belyankov (National Research Tomsk Polytechnic University, Tomsk) E-mail: Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.  

Рус

1. ГОСТ 23786–79. Трубы бурильные из алюми-ниевых сплавов. Технические условия. М.: Изд-во стан-дартов, 1990. 21 с.
2. Неразрушающий контроль: справочник: Т. 2: в 2 кн. / под ред. В. В. Клюева. Кн. 1. Контроль герме-тичности. Кн. 2. Вихретоковый контроль. М.: Машино-строение, 2003. 688 с.

Eng

1. Drill pipes of aluminium alloys. Specifications. (1990). Ru Standard No. GOST 23789-79. Moscow: Izdatel’stvo standartov.
2. Kliuev V.V. (Ed.). (2003). Non-destructive testing. Handbook. In 8 volumes. Vol. 2. In 2 books. Book 1. Leaktightness testing. Book 2. Eddy current testing. Moscow: Mashinostroenie.

Рус

Статью можно приобрести в электронном виде (PDF формат).

Стоимость статьи 250 руб. (в том числе НДС 18%). После оформления заказа, в течение нескольких дней, на указанный вами e-mail придут счет и квитанция для оплаты в банке.

После поступления денег на счет издательства, вам будет выслан электронный вариант статьи.

Для заказа статьи заполните форму:

Форма заказа статьи



Дополнительно для юридических лиц:


Type the characters you see in the picture below



.

Eng

This article  is available in electronic format (PDF).

The cost of a single article is 250 rubles. (including VAT 18%). After you place an order within a few days, you will receive following documents to your specified e-mail: account on payment and receipt to pay in the bank.

After depositing your payment on our bank account we send you file of the article by e-mail.

To order articles please fill out the form below:

Purchase digital version of a single article


Type the characters you see in the picture below



 

 

 

 

 

.

.

 

 
Поиск
На сайте?
Сейчас на сайте находятся:
 53 гостей на сайте
Опросы
Понравился Вам сайт журнала?
 
Баннер
Rambler's Top100 Яндекс цитирования